Transmisión multiportadora sin prefijo cíclico para comunicaciones radio de alta capacidad

Este trabajo fin de grado está orientado en una de las líneas de investigación seguidas en la actualidad para conseguir aumentar la capacidad de los sistemas de comunicaciones. Se ha centrado el trabajo en el marco de la modulación multiportadora Orthogonal Frequency Division Multiplexing (OFDM) por ser una de las técnicas más utilizadas en la actualidad en sistemas de banda ancha. El objetivo será aumentar la tasa de transmisión de un sistema de comunicaciones suprimiendo o reduciendo el prefijo cíclico, Cyclic Prefix (CP), perteneciente a OFDM. Se analizan y muestran las consecuencias en forma de interferencias que se tienen como resultado de no utilizar un CP mayor que la respuesta al impulso del canal. Las interferencias que se han encontrado son las denominadas como ISI (Inter-Symbol Interference) por no introducir un intervalo de guarda suficiente entre los símbolos OFDM e ICI (Inter-Carrier Interference) por la pérdida de ortogonalidad entre las subportadoras, provocando estas unos pésimos resultados en el sistema. Para poder combatir estos efectos se explicará y se implementará un algoritmo de cancelación de interferencias llamado “Cancelación residual de ISI” (RISIC). Este algoritmo consiste en realizar una combinación de cancelación de cola y una reconstrucción cíclica. Se ha analizado si los resultados obtenidos compensan el aumento de complejidad introducida en el sistema. Además, en este trabajo se investiga cómo esta técnica puede ser implementada en estándares actuales como Wimax (Worldwide Interoperability for Microwave Access) o LTE (Long Term Evolution), y así poder conseguir mayores velocidades de transmisión de datos.This final degree project deals with the research lines followed at present for increasing the capacity of communications systems. We have focused our work in multicarrier modulation Orthogonal Frequency Division Multiplexing (OFDM) for being one of the techniques used today in broadband systems. The goal that we want to achieve will be to increase the transmission rate of a communication system by eliminating or reducing the Cyclic Prefix (CP) pertaining to OFDM. Consequences are analyzed and displayed in the form of interference effects as result as not using a CP higher than the channel impulse response. The interferences that have been found are named ISI (Inter-Symbol Interference). This is because ISI doesn't introduce enough guard interval between OFDM symbols and ICI (Inter-Carrier Interference) for the loss of orthogonality between subcarriers and it provokes dismal system results. To combat these effects will be discussed and implemented an algorithm called interference cancellation "Residual ISI Cancellation" (RISIC). This algorithm is to perform a combination of tail cancellation cyclic reconstruction. We have analyzed if the results outweigh the increased complexity introduced into the system. In addition, this final degree project investigates how this technique can be implemented in existing standards such as WiMAX (Worldwide Interoperability for Microwave Access) or Long Term Evolution (LTE), so you can achieve higher data transmission speeds.Ingeniería de Sistemas de Comunicacione

An investigation into the fabrication parameters of screen-printed capacitive sensors on e-textiles

[EN] The design and development of textile-based capacitive sensors requires the implementation of textile capacitors with a determined capacitance. One of the main techniques to obtain these sensors is the screen-printing of conductive and dielectric inks on textiles. This paper investigates the fabrication parameters that have the most influence when designing and implementing a screen-printed capacitive sensor. In this work, a textile has been used directly as the dielectric part, influencing sensitively the value of the permittivity and the thickness of the dielectric of the capacitor. These are two fundamental parameters for the estimation of its capacitance. The choice of the conductive ink, its viscosity and solid content, as well as printing parameters, such as printing direction, also impact on the manner for obtaining the electrodes of the capacitive sensor. Although the resulting electrodes do not represent an important parameter for the estimation of the capacitance, it determines the selection of fabrics that can be printed. As a result of the investigation, the paper provides a guideline to choose the materials, such as fabrics or inks, as well as the printing parameters, to implement e-textile applications based on projected capacitive technologies. The experiments carried out on different fabrics and inks have provided results with capacities of less than 60 pF, the limit where the sensors based on capacitive technologies are located.The authors disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This work was supported by the Conselleria d'Economia Sostenible, Sectors Productius i Treball, through IVACE (Instituto Valenciano de Competitividad Empresarial) and cofounded by ERDF funding from the European Union (Application no. IMAMCI/2019/1). This work was also supported by the Spanish Government/FEDER funds (RTI2018-100910-B-C43) (MINECO/FEDER).Ferri, J.; Llinares Llopis, R.; Moreno, J.; Lidon-Roger, JV.; Garcia-Breijo, E. (2020). An investigation into the fabrication parameters of screen-printed capacitive sensors on e-textiles. Textile Research Journal. 90(15-16):1749-1769. https://doi.org/10.1177/0040517519901016S174917699015-16Gonçalves, C., Ferreira da Silva, A., Gomes, J., & Simoes, R. (2018). Wearable E-Textile Technologies: A Review on Sensors, Actuators and Control Elements. Inventions, 3(1), 14. doi:10.3390/inventions3010014Mostafalu, P., Tamayol, A., Rahimi, R., Ochoa, M., Khalilpour, A., Kiaee, G., … Khademhosseini, A. (2018). Smart Bandage for Monitoring and Treatment of Chronic Wounds. Small, 14(33), 1703509. doi:10.1002/smll.201703509Shi, H., Zhao, H., Liu, Y., Gao, W., & Dou, S.-C. (2019). Systematic Analysis of a Military Wearable Device Based on a Multi-Level Fusion Framework: Research Directions. Sensors, 19(12), 2651. doi:10.3390/s19122651Kim, K., Jung, M., Jeon, S., & Bae, J. (2019). Robust and scalable three-dimensional spacer textile pressure sensor for human motion detection. Smart Materials and Structures, 28(6), 065019. doi:10.1088/1361-665x/ab1adfFerri, J., Perez Fuster, C., Llinares Llopis, R., Moreno, J., & Garcia‑Breijo, E. (2018). Integration of a 2D Touch Sensor with an Electroluminescent Display by Using a Screen-Printing Technology on Textile Substrate. Sensors, 18(10), 3313. doi:10.3390/s18103313De Vos, M., Torah, R., Glanc-Gostkiewicz, M., & Tudor, J. (2016). A Complex Multilayer Screen-Printed Electroluminescent Watch Display on Fabric. Journal of Display Technology, 12(12), 1757-1763. doi:10.1109/jdt.2016.2613906Lin, X., & Seet, B.-C. (2017). Battery-Free Smart Sock for Abnormal Relative Plantar Pressure Monitoring. IEEE Transactions on Biomedical Circuits and Systems, 11(2), 464-473. doi:10.1109/tbcas.2016.2615603Ejupi, A., & Menon, C. (2018). Detection of Talking in Respiratory Signals: A Feasibility Study Using Machine Learning and Wearable Textile-Based Sensors. Sensors, 18(8), 2474. doi:10.3390/s18082474Polanský, R., Soukup, R., Řeboun, J., Kalčík, J., Moravcová, D., Kupka, L., … Hamáček, A. (2017). A novel large-area embroidered temperature sensor based on an innovative hybrid resistive thread. Sensors and Actuators A: Physical, 265, 111-119. doi:10.1016/j.sna.2017.08.030Komazaki, Y., & Uemura, S. (2019). Stretchable, printable, and tunable PDMS-CaCl2 microcomposite for capacitive humidity sensors on textiles. Sensors and Actuators B: Chemical, 297, 126711. doi:10.1016/j.snb.2019.126711Ng, C. L., & Reaz, M. B. I. (2019). Evolution of a capacitive electromyography contactless biosensor: Design and modelling techniques. Measurement, 145, 460-471. doi:10.1016/j.measurement.2019.05.031Ferri, J., Lidón-Roger, J., Moreno, J., Martinez, G., & Garcia-Breijo, E. (2017). A Wearable Textile 2D Touchpad Sensor Based on Screen-Printing Technology. Materials, 10(12), 1450. doi:10.3390/ma10121450Atalay, O. (2018). Textile-Based, Interdigital, Capacitive, Soft-Strain Sensor for Wearable Applications. Materials, 11(5), 768. doi:10.3390/ma11050768Yongsang Kim, Hyejung Kim, & Hoi-Jun Yoo. (2010). Electrical Characterization of Screen-Printed Circuits on the Fabric. IEEE Transactions on Advanced Packaging, 33(1), 196-205. doi:10.1109/tadvp.2009.2034536Lee, W. J., Park, J. Y., Nam, H. J., & Choa, S.-H. (2019). The development of a highly stretchable, durable, and printable textile electrode. Textile Research Journal, 89(19-20), 4104-4113. doi:10.1177/0040517519828992Chatterjee, K., Tabor, J., & Ghosh, T. K. (2019). Electrically Conductive Coatings for Fiber-Based E-Textiles. Fibers, 7(6), 51. doi:10.3390/fib7060051Gu, J. F., Gorgutsa, S., & Skorobogatiy, M. (2010). Soft capacitor fibers using conductive polymers for electronic textiles. Smart Materials and Structures, 19(11), 115006. doi:10.1088/0964-1726/19/11/115006Khan, S., Lorenzelli, L., & Dahiya, R. S. (2015). Technologies for Printing Sensors and Electronics Over Large Flexible Substrates: A Review. IEEE Sensors Journal, 15(6), 3164-3185. doi:10.1109/jsen.2014.2375203Zhang, Q., Wang, Y. L., Xia, Y., Zhang, P. F., Kirk, T. V., & Chen, X. D. (2019). Textile‐Only Capacitive Sensors for Facile Fabric Integration without Compromise of Wearability. Advanced Materials Technologies, 4(10), 1900485. doi:10.1002/admt.201900485Mukherjee, P. K. (2018). Dielectric properties in textile materials: a theoretical study. The Journal of The Textile Institute, 110(2), 211-214. doi:10.1080/00405000.2018.1473710Sadi, M. S., Yang, M., Luo, L., Cheng, D., Cai, G., & Wang, X. (2019). Direct screen printing of single-faced conductive cotton fabrics for strain sensing, electrical heating and color changing. Cellulose, 26(10), 6179-6188. doi:10.1007/s10570-019-02526-

A Wearable Textile 3D Gesture Recognition Sensor Based on Screen-Printing Technology

[EN] Research has developed various solutions in order for computers to recognize hand gestures in the context of human machine interface (HMI). The design of a successful hand gesture recognition system must address functionality and usability. The gesture recognition market has evolved from touchpads to touchless sensors, which do not need direct contact. Their application in textiles ranges from the field of medical environments to smart home applications and the automotive industry. In this paper, a textile capacitive touchless sensor has been developed by using screen-printing technology. Two different designs were developed to obtain the best configuration, obtaining good results in both cases. Finally, as a real application, a complete solution of the sensor with wireless communications is presented to be used as an interface for a mobile phone.The work presented is funded by the Conselleria d'Economia Sostenible, Sectors Productius i Treball, through IVACE (Instituto Valenciano de Competitividad Empresarial) and cofounded by ERDF funding from the EU. Application No.: IMAMCI/2019/1. This work was also supported by the Spanish Government/FEDER funds (RTI2018-100910-B-C43) (MINECO/FEDER).Ferri Pascual, J.; Llinares Llopis, R.; Moreno Canton, J.; Ibáñez Civera, FJ.; Garcia-Breijo, E. (2019). A Wearable Textile 3D Gesture Recognition Sensor Based on Screen-Printing Technology. Sensors. 19(23):1-32. https://doi.org/10.3390/s19235068S1321923Chakraborty, B. K., Sarma, D., Bhuyan, M. K., & MacDorman, K. F. (2017). Review of constraints on vision‐based gesture recognition for human–computer interaction. IET Computer Vision, 12(1), 3-15. doi:10.1049/iet-cvi.2017.0052Zhang, Z. (2012). Microsoft Kinect Sensor and Its Effect. IEEE Multimedia, 19(2), 4-10. doi:10.1109/mmul.2012.24Rautaray, S. S. (2012). Real Time Hand Gesture Recognition System for Dynamic Applications. International Journal of UbiComp, 3(1), 21-31. doi:10.5121/iju.2012.3103Karim, R. A., Zakaria, N. F., Zulkifley, M. A., Mustafa, M. M., Sagap, I., & Md Latar, N. H. (2013). Telepointer technology in telemedicine : a review. BioMedical Engineering OnLine, 12(1), 21. doi:10.1186/1475-925x-12-21Santos, L., Carbonaro, N., Tognetti, A., González, J., de la Fuente, E., Fraile, J., & Pérez-Turiel, J. (2018). Dynamic Gesture Recognition Using a Smart Glove in Hand-Assisted Laparoscopic Surgery. Technologies, 6(1), 8. doi:10.3390/technologies6010008Singh, A., Buonassisi, J., & Jain, S. (2014). Autonomous Multiple Gesture Recognition System for Disabled People. International Journal of Image, Graphics and Signal Processing, 6(2), 39-45. doi:10.5815/ijigsp.2014.02.05Ohn-Bar, E., & Trivedi, M. M. (2014). Hand Gesture Recognition in Real Time for Automotive Interfaces: A Multimodal Vision-Based Approach and Evaluations. IEEE Transactions on Intelligent Transportation Systems, 15(6), 2368-2377. doi:10.1109/tits.2014.2337331Khan, S. A., & Engelbrecht, A. P. (2010). A fuzzy particle swarm optimization algorithm for computer communication network topology design. Applied Intelligence, 36(1), 161-177. doi:10.1007/s10489-010-0251-2Abraham, L., Urru, A., Normani, N., Wilk, M., Walsh, M., & O’Flynn, B. (2018). Hand Tracking and Gesture Recognition Using Lensless Smart Sensors. Sensors, 18(9), 2834. doi:10.3390/s18092834Zeng, Q., Kuang, Z., Wu, S., & Yang, J. (2019). A Method of Ultrasonic Finger Gesture Recognition Based on the Micro-Doppler Effect. Applied Sciences, 9(11), 2314. doi:10.3390/app9112314Lien, J., Gillian, N., Karagozler, M. E., Amihood, P., Schwesig, C., Olson, E., … Poupyrev, I. (2016). Soli. ACM Transactions on Graphics, 35(4), 1-19. doi:10.1145/2897824.2925953Sang, Y., Shi, L., & Liu, Y. (2018). Micro Hand Gesture Recognition System Using Ultrasonic Active Sensing. IEEE Access, 6, 49339-49347. doi:10.1109/access.2018.2868268Ferri, J., Lidón-Roger, J., Moreno, J., Martinez, G., & Garcia-Breijo, E. (2017). A Wearable Textile 2D Touchpad Sensor Based on Screen-Printing Technology. Materials, 10(12), 1450. doi:10.3390/ma10121450Nunes, J., Castro, N., Gonçalves, S., Pereira, N., Correia, V., & Lanceros-Mendez, S. (2017). Marked Object Recognition Multitouch Screen Printed Touchpad for Interactive Applications. Sensors, 17(12), 2786. doi:10.3390/s17122786Ferri, J., Perez Fuster, C., Llinares Llopis, R., Moreno, J., & Garcia‑Breijo, E. (2018). Integration of a 2D Touch Sensor with an Electroluminescent Display by Using a Screen-Printing Technology on Textile Substrate. Sensors, 18(10), 3313. doi:10.3390/s18103313Cronin, S., & Doherty, G. (2018). Touchless computer interfaces in hospitals: A review. Health Informatics Journal, 25(4), 1325-1342. doi:10.1177/1460458217748342Haslinger, L., Wasserthal, S., & Zagar, B. G. (2017). P3.1 - A capacitive measurement system for gesture regocnition. Proceedings Sensor 2017. doi:10.5162/sensor2017/p3.1Cherenack, K., & van Pieterson, L. (2012). Smart textiles: Challenges and opportunities. Journal of Applied Physics, 112(9), 091301. doi:10.1063/1.474272

Integration of a 2D Touch Sensor with an Electroluminescent Display by Using a Screen-Printing Technology on Textile Substrate

[EN] Many types of solutions have been studied and developed in order to give the user feedback when using touchpads, buttons, or keyboards in textile industry. Their application on textiles could allow a wide range of applications in the field of medicine, sports or the automotive industry. In this work, we introduce a novel solution that combines a 2D touchpad with an electroluminescent display (ELD). This approach physically has two circuits over a flexible textile substrate using the screen-printing technique for wearable electronics applications. Screen-printing technology is widely used in the textile industry and does not require heavy investments. For the proposed solution, different layer structures are presented, considering several fabric materials and inks, to obtain the best results.This work was supported by Spanish Government/FEDER funds (grant number MAT2015-64139-C4-3-R (Mineco/Feder)). The work presented is also funded by the Conselleria d'Economia Sostenible, Sectors Productius i Treball, through IVACE (Instituto Valenciano de Competitividad Empresarial) and cofounded by ERDF funding from the EU. Application No.: IMAMCI/2017/1.Ferri Pascual, J.; Pérez Fuster, C.; Llinares Llopis, R.; Moreno Canton, J.; Garcia-Breijo, E. (2018). Integration of a 2D Touch Sensor with an Electroluminescent Display by Using a Screen-Printing Technology on Textile Substrate. Sensors. 18(10):3313-3326. https://doi.org/10.3390/s18103313S33133326181

Mutanome and expression of immune response genes in microsatellite stable colon cancer

The aim of this study was to analyze the impact of the mutanome in the prognosis of microsatellite stable stage II CRC tumors. The exome of 42 stage II, microsatellite stable, colon tumors (21 of them relapse) and their paired mucosa were sequenced and analyzed. Although some pathways accumulated more mutations in patients exhibiting good or poor prognosis, no single somatic mutation was associated with prognosis. Exome sequencing data is also valuable to infer tumor neoantigens able to elicit a host immune response. Hence, putative neoantigens were identified by combining information about missense mutations in each tumor and HLAs genotypes of the patients. Under the hypothesis that neoantigens should be correctly presented in order to activate the immune response, expression levels of genes involved in the antigen presentation machinery were also assessed. In addition, CD8A level (as a marker of T-cell infiltration) was measured. We found that tumors with better prognosis showed a tendency to generate a higher number of immunogenic epitopes, and up-regulated genes involved in the antigen processing machinery. Moreover, tumors with higher T-cell infiltration also showed better prognosis. Stratifying by consensus molecular subtype, CMS4 tumors showed the highest association of expression levels of genes involved in the antigen presentation machinery with prognosis. Thus, we hypothesize that a subset of stage II microsatellite stable CRC tumors are able to generate an immune response in the host via MHC class I antigen presentation, directly related with a better prognosis

Proyecto "Open Work University"

El sector educativo se ha visto afectado estos últimos tres años con la llegada de la pandemia, provocada por el COVID - 19. Por un lado, el sector educativo se mantuvo en incertidumbre al no tener todos los implementos necesarios para poder brindar una enseñanza de calidad a los universitarios. Ante ello, los estudiantes no estaban preparados para poder ejercer adecuadamente sus futuras, primeras, prácticas preprofesionales a las cuales postulan. Es por tal motivo que Open Work University nace como respuesta para ayudar a los universitarios a que complementen su perfil en su currículum; con el fin de facilitar su ingreso a distintos puestos de trabajo. Este proyecto de investigación consta de dos partes elementales. La primera etapa, se forma al reconocer la problemática y validar nuestra idea de negocios con el segmento al cual se dirigirá el proyecto, y reconocer que tan buena acogida tendría, si es que se implementa en el mercado. En la segunda etapa, se validó la solución y se realizaron proyecciones para reconocer que tan viable sería y cuánto serían las ganancias que se obtendría del aplicativo en cuestión. Finalmente, se desarrolló el aplicativo Open Work University, una plataforma dirigida a los estudiantes universitarios de los últimos ciclos, orientada a brindar cursos que complementen sus niveles de conocimientos en Office, idiomas, habilidades blandas, entre otros. De igual manera, que estos puedan establecer una red de contactos que faciliten su ingreso a empresas de su preferencia.The education sector has been affected in the last three years with the pandemic, caused by COVID - 19. On the one hand, this sector remained uncertain as it didn’t have all the tools to be able to provide quality education to university students. According to this matter, the students were not prepared to work adequately in their first future pre-professional internships to which they apply. It is for this reason that Open Work University was born as a response to help university students to complement their profile, in order to facilitate their entry into different jobs. This research project has two parts. The first stage is formed by recognizing the problem and validating our business idea with the target to which the project will be directed; also recognize how well received it would be. In the second stage, the solution was validated, and projections were made to recognize how viable it would be and how much profit would be obtained from the application in question. Finally, the Open Work University application was developed for university students in their last cycles, aimed at providing courses that complement their levels of knowledge in Office, Languages and Soft Skills. Also, they can establish a network of contacts that facilitate their entry into companies of their choice.Trabajo de investigació

Inverse Association between Dietary Iron Intake and Gastric Cancer: A Pooled Analysis of Case-Control Studies of the Stop Consortium

Background: Inconsistent findings have been reported regarding the relationship between dietary iron intake and the risk of gastric cancer (GC). Methods: We pooled data from 11 case-control studies from the Stomach Cancer Pooling (StoP) Project. Total dietary iron intake was derived from food frequency questionnaires combined with national nutritional tables. We derived the odds ratios (ORs) and 95% confidence intervals (CIs) for quartiles of dietary iron through multivariable unconditional logistic regression models. Secondary analyses stratified by sex, smoking status, caloric intake, anatomical subsite and histological type were performed. Results: Among 4658 cases and 12247 controls, dietary iron intake was inversely associated with GC (per quartile OR 0.88; 95% CI: 0.83-0.93). Results were similar between cardia (OR = 0.85, 95% CI = 0.77-0.94) and non-cardia GC (OR = 0.87, 95% CI = 0.81-0.94), and for diffuse (OR = 0.79, 95% CI = 0.69-0.89) and intestinal type (OR = 0.88, 95% CI = 0.79-0.98). Iron intake exerted an independent effect from that of smoking and salt intake. Additional adjustment by meat and fruit/vegetable intake did not alter the results. Conclusions: Dietary iron is inversely related to GC, with no difference by subsite or histological type. While the results should be interpreted with caution, they provide evidence against a direct effect of iron in gastric carcinogenesis

High-Throughput Sequencing of RNA Silencing-Associated Small RNAs in Olive (Olea europaea L.)

Small RNAs (sRNAs) of 20 to 25 nucleotides (nt) in length maintain genome integrity and control gene expression in a multitude of developmental and physiological processes. Despite RNA silencing has been primarily studied in model plants, the advent of high-throughput sequencing technologies has enabled profiling of the sRNA component of more than 40 plant species. Here, we used deep sequencing and molecular methods to report the first inventory of sRNAs in olive (Olea europaea L.). sRNA libraries prepared from juvenile and adult shoots revealed that the 24-nt class dominates the sRNA transcriptome and atypically accumulates to levels never seen in other plant species, suggesting an active role of heterochromatin silencing in the maintenance and integrity of its large genome. A total of 18 known miRNA families were identified in the libraries. Also, 5 other sRNAs derived from potential hairpin-like precursors remain as plausible miRNA candidates. RNA blots confirmed miRNA expression and suggested tissue- and/or developmental-specific expression patterns. Target mRNAs of conserved miRNAs were computationally predicted among the olive cDNA collection and experimentally validated through endonucleolytic cleavage assays. Finally, we use expression data to uncover genetic components of the miR156, miR172 and miR390/TAS3-derived trans-acting small interfering RNA (tasiRNA) regulatory nodes, suggesting that these interactive networks controlling developmental transitions are fully operational in olive

Measurement of the Splitting Function in &ITpp &ITand Pb-Pb Collisions at root&ITsNN&IT=5.02 TeV

Data from heavy ion collisions suggest that the evolution of a parton shower is modified by interactions with the color charges in the dense partonic medium created in these collisions, but it is not known where in the shower evolution the modifications occur. The momentum ratio of the two leading partons, resolved as subjets, provides information about the parton shower evolution. This substructure observable, known as the splitting function, reflects the process of a parton splitting into two other partons and has been measured for jets with transverse momentum between 140 and 500 GeV, in pp and PbPb collisions at a center-of-mass energy of 5.02 TeV per nucleon pair. In central PbPb collisions, the splitting function indicates a more unbalanced momentum ratio, compared to peripheral PbPb and pp collisions.. The measurements are compared to various predictions from event generators and analytical calculations.Peer reviewe